for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 1 general description features functional diagram typical applications 13 ghz low noise programmable divider (n = 1, 3) HMC861LP3E v00.0310 t he hm c 861lp3 e is a low noise programmable frequency divider in a 3 x 3 mm leadless surface mount package. t he divider can be programmed to divide from n = 1,3 in the 100 mhz to 13 ghz input frequency range. t he low phase noise and wide frequency range make this device ideal for high performance and wide band communication systems. low n oise floor: -152 dbc/hz at 100 khz offset programmable frequency divider, n = 1 or 3 wide bandwidth 100 mhz to 13 ghz 16 lead 3x3 mm s m t package: 9mm 2 electrical specifcations, t a = +25 c, vcc1 = vcc2 = +5v t he hm c 861lp3 e is ideal for: ? satellite communication systems ? point-to-point & point-to-multi-point radios ? military applications ? test equipment parameter c onditions min. t yp. max. u nits rf input characteristics max r f i nput frequency s ine wave or s quare wave i nput 13 ghz min r f i nput frequency [1] s ine wave or s quare wave i nput 0.1 ghz r f i nput power r ange -10 0 10 dbm divider output characteristics o utput power (see the pout plots for each division ratio) 2 dbm divider r atio n 1 3 ss b phase n oise @ 100 khz o ffset fin = 6 ghz, pin = 0 dbm, n = 1 -152 dbc/hz ss b phase n oise @ 100 khz o ffset fin = 6 ghz, pin = 0 dbm, n = 3 -153 dbc/hz logic inputs vi h i nput high v oltage 3 5 v vi l i nput low v oltage 0 0.4 v power supplies v cc1, v cc2 analog supply (see pin description table) 4.75 5 5.25 v current consumption i cc n = 1, s 0 = l 125 ma n = 3, s 0 = h 180 ma c ontrol bits 1 bit [1] s quare wave input waveform is recommended below 400 mhz for best phase noise performance. i f sine wave input waveform is used below 400 mhz, it is recommended that power input is > +5 dbm for best operation including phase noise performance.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 2 HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3) input sensitivity vs. temperature phase noise vs. temperature, fin = 6 ghz, pin = 0 dbm output harmonics, pin = 0 dbm output power vs. temperature, pin = 0 dbm phase noise vs. frequency, pin = 0 dbm reverse leakage, pin = 0 dbm divide-by-1 -170 -160 -150 -140 -130 -120 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 100mhz sq 100mhz sine 6 ghz 13 ghz ssb phase noise (dbc/hz) offset frequency (hz) -25 -20 -15 -10 -5 0 5 10 15 0 2 4 6 8 10 12 14 min pin +25c max pin +25c min pin +85c max pin +85c min pin -40c max pin -40c input power (dbm) input frequency (ghz) -50 -40 -30 -20 -10 0 10 0 2 4 6 8 10 12 14 pfeedthru 3rd harmonic output level (dbm) input frequency (ghz) -170 -160 -150 -140 -130 -120 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 +25c +85c -40c ssb phase noise (dbc/hz) offset frequency (hz) -6 -4 -2 0 2 4 6 0 2 4 6 8 10 12 14 +25c +85c -40c output power (dbm) input frequency (ghz) -50 -40 -30 -20 -10 0 both output ports terminated one output port terminated 1 2 3 4 5 6 7 8 9 10 11 12 13 14 power level (dbm) input frequency (ghz)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 3 HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3) divide-by-3 input sensitivity vs. temperature phase noise vs. temperature, fin = 6 ghz, pin = 0 dbm output harmonics, pin = 0 dbm output power vs. temperature, pin = 0 dbm phase noise vs. frequency, pin = 0 dbm reverse leakage, pin = 0 dbm -170 -160 -150 -140 -130 -120 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 100mhz sq 100mhz sine 6 ghz 13 ghz offset frequency(hz) ssb phase noise (dbc/hz) -25 -20 -15 -10 -5 0 5 10 15 0 2 4 6 8 10 12 14 min pin +25c max pin +25c min pin +85c max pin +85c min pin -40c max pin -40c input power (dbm) input frequency (ghz) -60 -50 -40 -30 -20 -10 0 10 0 2 4 6 8 10 12 14 pfeedthru 3rd harmonic output level (dbm) input frequency (ghz) -170 -160 -150 -140 -130 -120 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 +25c +85c -40c ssb phase noise (dbc/hz) offset frequency (hz) -6 -4 -2 0 2 4 6 0 2 4 6 8 10 12 14 +25c +85c -40c output power (dbm) input frequency (ghz) -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 both output ports terminated one output port terminated 1 2 3 4 5 6 7 8 9 10 11 12 13 14 power level (dbm) input frequency (ghz)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 4 absolute maximum ratings reliability information rf i nput power 13 dbm s upply v oltage ( vcc) 5.5v c ontrol inputs (s0) 5.5v s torage t emperature -65 to +125 c esd s ensitivity (hbm) class 1a junction t emperature to maintain 1 million hour mttf 150 c n ominal junction t emperature (t = 85 c and pin = 10 dbm)) 108 c t hermal r esistance (junction to g n d paddle, 5v s upply) 25 c/w o perating t emperature -40 to +85 c digital control input voltages s tate s 0 low 0 to 0.4 v high 3 v to 5 v electrostatic sensitive device observe handling precautions programming truth table for frequency division ratios s 0 divider r atio ( n ) 0 1 1 3 0 = logic low 1 = logic high n ote: v cc1, v cc2 must be applied before logic. HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3) icc vs. vcc 75 100 125 150 175 200 225 4.7 4.8 4.9 5 5.1 5.2 5.3 n = 1 n = 3 operating current (ma) vcc (v)
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 5 HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3) outline drawing part n umber package body material lead finish m s l r ating package marking [1] hm c 861lp3 e r oh s -compliant low s tress i njection molded plastic 100% matte s n m s l1 [2] 861 xxx x [1] 4-digit lot number xxxx [2] max peak refow temperature of 260 c package information notes : 1. leadframe material: copper alloy 2. dimensions are in inches [millimeters]. 3. lead spacing tolerance is non-cumulative 4. pad burr length shall be 0.15mm maximum. pad burr height shall be 0.05mm maximum. 5. package warp shall not exceed 0.05mm. 6. all ground leads and ground paddle must b e so ld ere d to p c b r f g roun d. 7. refer to hittite application note for suggested pcb land pattern.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 6 HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3) pin description pin n umber function description i nterface s chematic 1, 4, 8, 9, 12, 14, 15 g n d ground: backside of package has exposed metal ground slug which must be connected to r f/d c ground. 2 in r f i nput must be d c blocked. 3 nin r f i nput 180 out of phase with pin 2 for differential operation. ac ground for single ended operation. 5 s 0 c m os compatible division ratio control bit. s ee programming truth table. 6 g n d i nternally connected to circuitry, must be connected to rf/dc ground for proper operation. 7 nc t he pins are not connected internally; however, all data shown herein was measured with these pins connected to r f/d c ground externally. 10 nout divider output 180 out of phase with pin 11. r f output must be d c blocked. 11 out divided o utput. r f output must be d c blocked. 13, 16 v cc1, v cc2 s upply voltage 5 v . c onnect both pins to +5 v supply.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 7 evaluation pcb schematic HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3) notes : 1. t he shorting link from p c b ground to pin 6 must be installed for proper operation. 2. capacitors c1, c2, c3, and c4 are broadband multilayer capacitors, american technical cermaics part number atc530l. the 100 nf capacitance value is per atc datasheet.
for price, delivery and to place orders: hittite microwave corporation, 20 alpha road, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order on-line at www.hittite.com application support: phone: 978-250-3343 or apps@hittite.com frequency divi d ers & detectors - s m t 4 4 - 8 evaluation pcb list of materials for evaluation pcb eval01-HMC861LP3E [1] i tem description j1 - j3 connector, sma, female j4 d c c onnector header, molex 2mm c 1 - c 4 100 nf c apacitor, broadband, 0402 c 5, c 6 1000 pf c apacitor, 0402 pkg. c 7, c 8 4.7 uf c apacitor, 1206 r 3 10 k o hm r esistor, 0402 v cc1, v cc2 d c pin, 0.040" dia. u 1 hm c 861lp3 e , programmable divider p c b [2] 119349 e valuation board [1] r eference this number when ordering complete evaluation p c b [2] circuit board material: rogers 4350 or arlon 25fr t he circuit board used in the application should use r f circuit design techniques. s ignal lines should have 50 o hm impedance while the package ground leads and backside ground paddle should be con - nected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. t he evaluation circuit board shown is available from hittite upon request. HMC861LP3E v00.0310 13 ghz low noise programmable divider (n = 1, 3)
|
